CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz] ARKANCE | CONTACT - CZ | SK | EN | DE
Over 1.096.000 registered users (EN+CZ). AutoCAD tips, Inventor tips, Revit tips. Try the new precise Engineering calculator and the updated Barcode generator. New AutoCAD 2026 commands and variables.
RSS channel - CAD tips RSS tips
RSS discussions

Discussion Discussion forum

?
CAD discussions, advices, exchange of experience

CAD Forum - Homepage CAD discussion forum - ask any CAD-related questions here, share your CAD knowledge on AutoCAD, Inventor, Revit and other Autodesk software with your peers from all over the world. To start a new topic, choose an appropriate forum.

Please abide by the rules of this forum.
This is a peer-to-peer forum. The forum doesn't replace the official direct technical support provided by ARKANCE for its customers.
How to post questions: register or login, go to the specific forum and click the NEW TOPIC button.
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Topic ClosedSweep command problem
 Post Reply Post Reply
Author
  Topic Search Topic Search  Topic Options Topic Options
4riders View Drop Down
Newbie
Newbie


Joined: 03.Jan.2015
Location: Romania
Using: autocad 2013
Status: Offline
Points: 3 		Direct Link To This Post Topic: Sweep command problem
    Posted: 18.Jan.2016 at 08:09
Hello, 
i try to  do sweep command. i have used with no problems until now.
When i used sweep command it was sweeping this shape into a solid.
Now, when i sweep it converts it into a surface.
Do you have a solution to sweep this shape into a solid and not in a surface ?
uploads/526420/dormitor_lupu.dwg
Back to Top
4riders View Drop Down
Newbie
Newbie


Joined: 03.Jan.2015
Location: Romania
Using: autocad 2013
Status: Offline
Points: 3 		Direct Link To This Post Posted: 18.Jan.2016 at 08:58
i tryed sweep command with surface mode 1 - 0 but it creates surface or nurbs surfaces.
i tryed extrude command with solid mode on but it says :
path curve is coplanar with or tangent to the plane of the profile curve
Back to Top
John Connor View Drop Down
Senior Member
Senior Member


Joined: 01.Feb.2011
Location: United States
Using: AutoCAD 2018
Status: Offline
Points: 7175 		Direct Link To This Post Posted: 18.Jan.2016 at 12:27
You must be doing something wrong then.  The key line in the error message is the last one that starts "curve path is coplanar...."  You'll have to try again.
"Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance."

<<AutoCAD 2015>>
Back to Top
philippe JOSEPH View Drop Down
Senior Member
Senior Member


Joined: 14.Mar.2011
Location: France
Using: AutoCAD Mechanical 2017
Status: Offline
Points: 1493 		Direct Link To This Post Posted: 18.Jan.2016 at 12:58
Hello 4riders and John, I have open your file and found :
5 Solids OK , 6 closed polylines OK for the command : EXTRUDE and 2 non coplanar lines.
Please let us know on which entity you have a problem.
Back to Top

Related CAD tips:


 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down



This page was generated in 0,331 seconds.
CADforum
CADforum
Tips and tricks, support, utilities, help, discussions on AutoCAD, LT, Inventor, Revit, Map, Civil 3D, 3ds Max, Fusion, Forma, Vault, PowerMill and other Autodesk software (community support by ARKANCE). See About CADforum.
Copyright © 2025 | Advertise with us | Online privacy
ARKANCE - Autodesk Platinum Partner & Training Center & Services Partner
CONTACT:
webmaster.cz@arkance.world | tel. +420 910 970 111
FB LN TW YT TW Blog RSS
.
TOPlist