![CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]](/common/arkance_186.png "CAD Forum - ARKANCE Community - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]")
CAD FORUM - TIPS & TRICKS | UTILITIES | DISCUSSION | BLOCKS | SUPPORT | HELP & ADVICE
Over 1.132.000 registered users (EN+CZ).
AutoCAD tips, Inventor tips, Revit tips, Civil tips, Fusion tips.
See the new Beam calculator, Engineering calculator, Tolerances, Spirograph generator and Regression curves in the Converters section.
New AutoCAD 2027 commands and sys.variables
Discussion forum
?CAD discussions, advices, exchange of experience
CAD discussion forum - ask any CAD-related questions here, share your CAD knowledge on AutoCAD, Inventor, Revit and other Autodesk software with your peers from all over the world. To start a new topic, choose an appropriate forum.
Please abide by the rules of this forum.
This is a peer-to-peer forum. The forum doesn't replace the official direct technical support provided by ARKANCE for its customers.
How to post questions: register or login, go to the specific forum and click the NEW TOPIC button.
|
Connect line to a circle
Post Reply 
|
| Author | |
HarunT 
Newbie 
Joined: 02.Mar.2017 Location: United Kingdom Using: Autocad 2014 Status: Offline Points: 2 |
 Topic: Connect line to a circlePosted: 02.Mar.2017 at 16:53 |
|
uploads/710612/images_1.pdf
Hi there, how can i connect this line to any point on the circle? this is what it looks like when i zoom in. hope you can help.
|
|
|
HT
|
|
 |
|
|
Vladimir Michl
Moderator Group 
Joined: 26.Jul.2007 Location: Czech Republic Using: Autodesk software Status: Offline Points: 2188 |
Posted: 02.Mar.2017 at 16:59 |
|
If you use OSNAP, your geometry should be precise - despite it may be displayed disconnected in extreme zoom levels.
Make sure your geometry is not too far from the world origin (0,0,0).
|
|
|
Vladimir Michl (moderator)
LinkedIn, Autodesk Expert Elite |
|
|
|
|
John Connor
Senior Member 
Joined: 01.Feb.2011 Location: United States Using: AutoCAD 2018 Status: Offline Points: 7175 |
Posted: 02.Mar.2017 at 17:08 |
|
If the line is not connected to a quadrant or tangent to the circle then to connect it to any point on the circle try drawing a temporary line that intersects the circle then use the INTERSECTION osnap to make the connection.
|
|
|
"Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance."
<<AutoCAD 2015>> |
|
|
|
|
Kent Cooper
Senior Member
Joined: 12.Mar.2013 Location: United States Using: AutoCAD2020, 2023 Status: Offline Points: 687 |
Posted: 02.Mar.2017 at 18:58 |
|
If you used some Osnap mode to put it on the Circle, or Trim or Extend, and if this is Zoomed significantly in since then, it's just a matter of display resolution. REGEN and it will probably meet visually [it really does meet geometrically already]. It's a function of the way curves are segmented in display only. To at least lessen the effect, go into VIEWRES and give it a higher Circle Zoom Percentage.
|
|
|
|
Topic Options|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
This page was generated in 0,195 seconds.
CADforum
Tips and tricks, support, utilities, help, discussions on AutoCAD, LT, Inventor, Revit, Map, Civil 3D, 3ds Max, Fusion, Forma, Vault, PowerMill and other Autodesk software (community support by ARKANCE). See About CADforum.
Copyright © 2026 | Advertise with us | Online privacy
