CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz] ARKANCE | CONTACT - CZ | SK | EN | DE
Over 1.099.000 registered users (EN+CZ). AutoCAD tips, Inventor tips, Revit tips. Try the new precise Engineering calculator and the updated Barcode generator. New AutoCAD 2026 commands and variables.
Be.Smart Concrete webinar - extend your Revit
RSS channel - CAD tips RSS tips
RSS discussions

Discussion Discussion forum

?
CAD discussions, advices, exchange of experience

CAD Forum - Homepage CAD discussion forum - ask any CAD-related questions here, share your CAD knowledge on AutoCAD, Inventor, Revit and other Autodesk software with your peers from all over the world. To start a new topic, choose an appropriate forum.

Please abide by the rules of this forum.
This is a peer-to-peer forum. The forum doesn't replace the official direct technical support provided by ARKANCE for its customers.
How to post questions: register or login, go to the specific forum and click the NEW TOPIC button.
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Topic Closedchange in lisp required
 Post Reply Post Reply
Author
  Topic Search Topic Search  Topic Options Topic Options
thinker View Drop Down
Groupie
Groupie


Joined: 08.Jun.2013
Location: United Arab Emirates
Using: AutoCAD2021
Status: Offline
Points: 35 		Direct Link To This Post Topic: change in lisp required
    Posted: 08.Jun.2013 at 14:42
Hi every one!
I am working on road cross section and using this lisp to show the levels and offset from center line, I have to keep vertical scal double to horizantal scale so when I use this it show double value of Y-axisCry I want change in this lisp that it shows the half value of Y-axis any body can help thanks
 
uploads/381267/LEVEL_Y-X.lsp
Back to Top
Kent Cooper View Drop Down
Senior Member
Senior Member


Joined: 12.Mar.2013
Location: United States
Using: AutoCAD2020, 2023
Status: Offline
Points: 686 		Direct Link To This Post Posted: 10.Jun.2013 at 14:52
If I understand what you're asking, try changing this line:
 (setq north (strcat " " (rtos (cadr pt2) 2 3)))
to this:
 (setq north (strcat " " (rtos (/ (cadr pt2) 2) 2 3)))
Back to Top
thinker View Drop Down
Groupie
Groupie


Joined: 08.Jun.2013
Location: United Arab Emirates
Using: AutoCAD2021
Status: Offline
Points: 35 		Direct Link To This Post Posted: 11.Jun.2013 at 05:17
Thank you very much Kent cooper I check it little bit it is working properly Clap i will check more then i will give comments 
Back to Top
thinker View Drop Down
Groupie
Groupie


Joined: 08.Jun.2013
Location: United Arab Emirates
Using: AutoCAD2021
Status: Offline
Points: 35 		Direct Link To This Post Posted: 11.Jun.2013 at 13:11
Thanks again Mr.Kent cooper I check it, it is working perfectly
Back to Top
Kent Cooper View Drop Down
Senior Member
Senior Member


Joined: 12.Mar.2013
Location: United States
Using: AutoCAD2020, 2023
Status: Offline
Points: 686 		Direct Link To This Post Posted: 12.Jun.2013 at 15:44
You're welcome -- it's good to hear that I understood correctly what you were trying to do.
Back to Top

Related CAD tips:


 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down



This page was generated in 0,075 seconds.
CADforum
CADforum
Tips and tricks, support, utilities, help, discussions on AutoCAD, LT, Inventor, Revit, Map, Civil 3D, 3ds Max, Fusion, Forma, Vault, PowerMill and other Autodesk software (community support by ARKANCE). See About CADforum.
Copyright © 2025 | Advertise with us | Online privacy
ARKANCE - Autodesk Platinum Partner & Training Center & Services Partner
CONTACT:
webmaster.cz@arkance.world | tel. +420 910 970 111
FB LN TW YT TW Blog RSS
.
TOPlist