![CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]](/common/arkance_186.png "CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]")
CAD FORUM - TIPS & TRICKS | UTILITIES | DISCUSSION | BLOCKS | SUPPORT | HELP & ADVICE
Over 1.106.000 registered users (EN+CZ).
AutoCAD tips, Inventor tips, Revit tips, Civil tips, Fusion tips.
Try the new precise Engineering calculator.
New AutoCAD 2026 commands and sys.variables and env.variables,.
Discussion forum
?CAD discussions, advices, exchange of experience
CAD discussion forum - ask any CAD-related questions here, share your CAD knowledge on AutoCAD, Inventor, Revit and other Autodesk software with your peers from all over the world. To start a new topic, choose an appropriate forum.
Please abide by the rules of this forum.
This is a peer-to-peer forum. The forum doesn't replace the official direct technical support provided by ARKANCE for its customers.
How to post questions: register or login, go to the specific forum and click the NEW TOPIC button.
|
Modify-Scale problems with dims
Post Reply 
|
| Author | |
StevieG 
Newbie 
Joined: 30.Jul.2008 Location: United Kingdom Status: Offline Points: 2 |
 Topic: Modify-Scale problems with dimsPosted: 30.Jul.2008 at 12:59 |
|
As a Site Engineer I frequently have to convert an architects drawing in mm to a different grid system in metres.
Rotate and Move sort out the grid position and <Modify -Scale> with a scale factor of 0.001 sets the drawing in metres. This frequently leaves me with a drawing masked by dimensions that are still at the old scale. I have altered the"Fit" of dims in DimStyles or properties (select and Rclick) with some success but it is both tedious and not always 100% effective. There always seem to be some dims that don't respond. Is there a better way?please, please tell me there is.
|
|
 |
|
|
Vladimir Michl
Moderator Group 
Arkance Systems CZ Joined: 26.Jul.2007 Location: Czech Republic Using: Autodesk software Status: Offline Points: 2144 |
Posted: 30.Jul.2008 at 14:44 |
|
It depends on the dimension style(s) used in a particular drawing. Try to set the DIMSCALE value.
|
|
|
Vladimir Michl (moderator)
ARKANCE - https://arkance.world - Autodesk Platinum Partner |
|
|
|
|
StevieG
Newbie
Joined: 30.Jul.2008 Location: United Kingdom Status: Offline Points: 2 |
Posted: 31.Jul.2008 at 14:09 |
|
Thanks Vladimir. I tried DIMSCALE command as you suggested with some success. I've previously used dimscale overall and dimscale linear from the properties menu. Does this alter the same parameter in Autocad?
Prompted by your comment I looked up DIMSCALE in the help pages and I see that it doesn't apply to all dimensions. I think this could be why I can't fully solve the problem.
If designers kept dimensions on a separate layer they could be switched off en masse but they sometimes mix them in with the drawing layers.
It has just occurred to me that I can select each class of dimension through <Edit-SelectAll-Properties> then place them on new individual layers. Any that don't respond to DIMSCALE can be switched off.
Thanks for the chat.
steve Edited by StevieG - 31.Jul.2008 at 14:09 |
|
|
|
Topic Options|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
This page was generated in 0,234 seconds.
CADforum
Tips and tricks, support, utilities, help, discussions on AutoCAD, LT, Inventor, Revit, Map, Civil 3D, 3ds Max, Fusion, Forma, Vault, PowerMill and other Autodesk software (community support by ARKANCE). See About CADforum.
Copyright © 2025 | Advertise with us | Online privacy
