PlotDWGarr + LayDWGarr + wbDWGarr + pcDWGarr (by ARKANCE)
-----------------------------------------------------------------

(EN)

If you get a DWG drawing which contains multiple frames (with individual drawings) composed as an array in the modelspace,
you can use the following utility that "batch plots" these sub-drawings, or - better - splits them into individual layouts,
that can be batch-plotted using the PUBLISH command, or splits them to separate DWG drawing files or defines plot
configurations (page setups) covering them.

+-----+ +-----+ +------+
|     | |     | |      |
+-----+ +-----+ +------+
+-----+ +-----+ +------+
|     | |     | |      |
+-----+ +-----+ +------+


After you load the utility with APPLOAD, you can use the PlotDWGarr command to start the batch plotting (to the curent print
device, with the current parameters - see your last PLOT) of all frames in the array, or the LayDWGarr command to generate
new layouts containing the individual "drawings" (frames), or the wbDWGarr command to "explode" the frames to separate DWGs,
or the pcDWGarr command to create Page setups (from a template) and publishing them automatically.

In all cases, the application first prompts fo the shape of the rectangular array with the "drawings". You will sequentially
enter the top left point (1), the size of a single frame (2), the distance between columns (3) and rows (4), the number of
columns and rows (see the picture). Possible missing frames are ignored (not plotted). See:
http://www.cadforum.cz/en/plotting-a-series-of-drawing-frames-composed-in-a-dwg-drawing-tip7585

1-----+ 3-----+ +------+
|     | |     | |      |
+-----2 +-----+ +------+
4-----+ +-----+ +------+
|     | |     | |      |
+-----+ +-----+ +------+

You can also specify the frames by selecting existing rectangles (in a specified layer) or by existing block references.

Since V1.8 you can also use texts in a specified layer or block with an attribute to set frame names.

As a result, either a respective number of plots is printed (per rows, or per colums), or a series of numbered layouts, or a
series of DWG drawing files or plot configs is created. The generated layouts are created from the layout template
"(PlotArrTemplate)" or a picked one. In this template you can predefine the viewport size, its scale, page setup, etc.).
Make sure you have locked the viewport in the template. You can the plot this series in one go using the PUBLISH command.
For the pcDWGarr command, the template page setup "PlotArrTemplate" is used.

NB: You can preset the Rows/Columns processing with (setq dwgarr:dofirst "Columns") and the plotconfig template with
(setq pcDWGarrTemplate "MyPageSetup")

----------------------------------------------------------------------------------------------------------------------------

(CZ)

1. Natte aplikaci pkazem _appload

2. Tisk (na nastaven zazen)
- Nastavte si parametry tisku v PageSetup, tak jak m jedna strnka vypadat (zazen, naku, centrovat, atd.)
- spuste pkaz PLOTDWGARR
 Aplikace se postupn pt na body:
 - lev horn bod celho pole vkres
 - prav doln bod prvnho rmeku (mono i zadat jako velikost "ka,vka")
 - ku "buky" pole - tedy od LH rohu jednoho rmeku k LH rohu vedlejho rmeku doprava
 - vku "buky" pole - tedy od LH rohu jednoho rmeku k LH rohu nejbliho rmeku pod (dol)
 - poet sloupc
 - poet dk (ppadn chybjc vkresy v poli se nevykresluj)
 - vykreslovat lze po dcch nebo po sloupcch

3. Vytven rozvren (dle vzorovho rozvren)
- Vytvote vzorov rozvren s nzvem (PlotArrTemplate) nzev vetn zvorek, ve vzhledu jak maj vypadat automaticky vytven rozvren (pohled nesm bt zamen)
- spuste pkaz LayDWGarr
 Aplikace se postupn pt na body:
 - lev horn bod celho pole vkres
 - prav doln bod prvnho rmeku (mono i zadat jako velikost "ka,vka")
 - ku "buky" pole - tedy od LH rohu jednoho rmeku k LH rohu vedlejho rmeku doprava
 - vku "buky" pole - tedy od LH rohu jednoho rmeku k LH rohu nejbliho rmeku pod (dol)
 - poet sloupc
 - poet dk (ppadn chybjc vkresy v poli se nepevdj na rozvren)
 - postupovat lze po dcch nebo po sloupcch

4. Vytven samostatnch vkres
- Spuste pkaz wbDWGarr
 Aplikace se postupn pt na body:
 - lev horn bod celho pole vkres
 - prav doln bod prvnho rmeku (mono i zadat jako velikost "ka,vka")
 - ku "buky" pole - tedy od LH rohu jednoho rmeku k LH rohu vedlejho rmeku doprava
 - vku "buky" pole - tedy od LH rohu jednoho rmeku k LH rohu nejbliho rmeku pod (dol)
 - poet sloupc
 - poet dk (ppadn chybjc vkresy v poli se neexportuj)
 - postupovat lze po dcch nebo po sloupcch

5. Vytven samostatnch vzhled strnek (plot configuration)
- Spuste pkaz pcDWGarr
- vyberte rmce
- jsou vytvoeny vzhledy ze ablony PlotArrTemplate a je sputno publikovn

Od verze V1.8 mete tak pouvat texty v zadan hladin nebo bloky s atributem pro nastaven nzv rmek.

Nzev nastavenho vzorovho rozvren v aplikaci muete zmnit pkazem: (setq LayDWGarrTemplate "nazev_rozvrzeni")

POZN: vechny daje se zapamatuj, take pt sta jen "odentrovat"
POZN: mete pednastavit zpracovn po sloupcch/po dcch pomoc (setq dwgarr:dofirst "Columns")

TIP: Vzhled tisku a tiskrnu jednotlivch rozvren mete zmnit pmo v okne PUBLISH, dle nastaven uloenho vzhledu strnky v libovolnm souboru DWG pes import...


--------
Versions:
V1.10- LayDWGarr can use any existing layout as a template
V1.9 - Text filtering, fixed frame naming, autocorrecting invalid frame names, visual picks
V1.8 - Registry key, ANSI formats, frame naming (by text or by attribute), output folder, LT support, signed
V1.7 - pcDWGarr added for creating plot configurations and publishing them automatically
     - Rectangle and Block options added to handle irregular (manually placed) frames
V1.6 - wbDWGarr added for exporting to separate DWGs
V1.5 - Generated layouts are sorted sequentially
V1.4 - Fileplots supported, with sequential numbering (e.g. for PDF)
V1.3 - Selectable - first Columns/Rows 
V1.1 - LayDWGarr command added

License: plotDWGarr is a free utility by ARKANCE,
do not publish it online on other than ARKANCE's
web servers, do not sell, lend or exchange it.
CZ: plotDWGarr je bezplatn utilita firmy ARKANCE pro
zkaznky firmy ARKANCE

-------------------------------------------------------------
Contact:
Arkance Systems CZ
Libalova 2348/1, 149 00 Praha 4, Czech Republic
info.cz@arkance.world   www.arkance.world   www.cadforum.cz
