Autodesk překvapil uvedením dalšího Service Packu ještě i pro dvě verze "starou" release - Inventor 2010. Pokud tedy zatím nepoužíváte aktuální Inventor 2012 (resp. Product Design Suite) ani verzi 2011, stáhněte si SP4 pro Inventor 2010 (s nebo bez Subscription Advantage Packu) ze stránky Download). Zde je přehled oprav v SP4: 

Autodesk Inventor
Professional 2010



Stress Analysis


When saving using "Save Copy As", Stress Analysis file names do not update.
FEA mesh warning labels remain, even if the mesh is successfully generated
in subsequent meshing operations.
Return to Top



Tube & Pipe


In certain circumstances, Place Fitting fails for non-vertical route paths.

Return to Top


Autodesk Inventor 2010



API


Inventor crashes when saving a drawing where references have been replaced.
Updating a drawing document which contains replaced references in invisible
mode, causes Inventor to become unstable.
The OnFileResolution event does not provide the referenced file type and
redirection stream index.
If the last active view in an assembly is Master,
GetLastActiveDesignViewRepresentation causes errors.
Cannot read the property ReferencedDocumentDescriptors of a Substitute.
PartDocument.FileSaveCounter is increased by one when saving a non-dirtied
document.
GetLevelOfDetailRepresentations within the Apprentice FileManager returns
different Levels of Detail order before and after you open a document.
RelativeFileName returns incorrect results in event OnFileResolution.

Return to Top



Assembly Modeling


Activating a substitute subassembly causes constraints failures.
The overridden mass of a flexible reference sub-assembly is counted
incorrectly in the mass of the parent assembly.
Demote corrupts the Degree of Freedom settings inside the occurrence tab.
Inventor crashes when you replace a frame in an assembly.

Return to Top



Content Center


The value of a template parameter disappears for a Part that is published to
the Content Center.
The $ character is invalid in Content Center file or folder names.
The Content Center appears empty until you log out and log back in to the
Vault Server.
When publishing an Inventor 11 part file to the Content Center, unexpected
behavior occurs.
Return to Top



Drawing Manager


Two Bend Notes display for the same bend line - one shows Up, and the other
shows Down.
Cannot reattach dimensions to center lines.
When you open a drawing, dimensions are disconnected from geometry.
After applying Service Pack 2, you cannot attach annotations to ordinate
dimension sets.
Inventor crashes when inserting a feature control frame.
Hole Note information inside a drawing is incorrect when used for derived
and scaled parts.
If Microsoft Office 2010 is installed, the exporting of a parts list fails.
Inventor unexpectedly exits when opening migrated Inventor R11 IDW files.
A Detail View of an Aligned Section View loses data.
Cannot disable reflections in drawings.
Return to Top



Framework


VBA macros take longer to execute than launching the VBA Editor once, in
64-bit Inventor.
A crash occurs when opening a part file with over 2000 iFeature files in the
iFeature Catalog.
Return to Top



Frame Generator


Inventor crashes when the profile of a frame is changed to a different
standard or profile type.
Return to Top



Part Modeling


Recompute of some features used as iFeatures causes errors.
Inventor unexpectedly exits after you use the Split command followed by
other operations on a part body.
iFeatures fail after Rebuild All.
The iFeature Insert dialog box shows "Create Package" instead of the
description of the iFeature.
Inventor unexpectedly exits if you perform edits with Inventor 2010 on a
Taper threaded hole made with Inventor 11.
Work Feature edits do not update the feature in the 3D Sketch environment.
Inventor crashes when a Chamfer or Fillet feature recomputes on an unstable
edge.
Return to Top



Sketch


Performance is slow when moving an imported logo in a 2D sketch.

Return to Top



Studio


Inventor crashes during rendering.
Return to Top



Translators


Export to PDF creates unreadable font characters.
Inventor crashes exporting a spline surface in the STEP format.

Return to Top



Vault


Refresh from Vault overwrites any locally saved and checked out files.
Inventor 2010 does not see Content Center Ownership Transfers in a
Replicated Vault Server 2011.
Return to Top