Zobrazit plnou verzi příspěvku: Uveden SP2 pro Inventor 2011

Vladimír Michl
19.05.2011, 16:44
Pro uživatele Inventoru 2012 (vč. verze Professional a vč. české verze) byl uveden nový Service Pack 2. Všechny 4 verze Service Packu 2 najdete též na stránce Download.
 
Pro instalaci SP2 je potřeba mít nainstalován SP1 a je potřeba vybrat správnou verzi - 32/64-bit a verzi se SAP nebo bez SAP (tedy zda máte nainstalován Subscription Advantage Pack).
 
Přehled oprav:
 

Autodesk Inventor Professional 2011




Dynamic Simulation


Blank items in Mechanism Status display after you run Unknown Force.
CER: A crash occurs with automatic update of Dynamic Simulation joints after assembly restructure.
In Win7/Vista, you cannot save a .cgd curve file to a location other than the assembly file.
When you re-open an assembly saved in simulation mode, the Automatic joint creation option is checked.
Return to Top



Stress Analysis


A memory leak occurs after you generate a report with images.
Contacts information does not display in the Report.
If you use invalid characters in a Report name, the message "Address not valid" displays in the .mht report.
Material section for Weldment assemblies is missing in Report.
Maximum value label displays the edited maximum value of the color bar.
Memory usage increases while you run Animate.
NG: Various "Degenerate Element" meshing issues occur.
Out of date flag is shown changing stop criteria to a higher value than already achieved.
While you set an absolute value for the color bar, negative probe values do not change to absolute values.
Return to Top



Frame Analysis


CER: Various crashes occur with simulate command and beam customization.
CER: Various crashes occur with beam model update.
When you leave the Frame Analysis environment, material opacity set at translucent changes to opaque.
If you use invalid characters in a Report name, the message "Address not valid" displays in the .mht report.
Return to Top



Tooling


Cannot Start Windows in Safe Mode after installation of Inventor 2011.
Return to Top



Tube & Pipe


CER: Inventor crashes on a 64 bit machine when you use Make Adaptive to the instanced Tube & Pipe Runs.
Return to Top



Cable & Harness


Improved performance in AutoRoute with high Wire count.
Return to Top


Autodesk Inventor 2011



API


Addition of radius or diameter dimensions fails on a circular arc projected from a B-spline curve.
AddWithOptions does not place an occurrence in the correct position.
DrawingDocument.Update fails after you change the references for certain data in the drawing document.
Enhance the OnFileResolution event to provide the referenced file type using Context("IsForeignFile").
FileSaveCount always increases by one, even on saves of un-dirtied part documents.
In FileManager, GetLevelOfDetailRepresentations returns a different order before and after you open an assembly document.
NG: DesignProject.Activate causes the alterable pointing to the design project references to an invalid design project.
RelativeFileName within the FileAccessEvents.OnFileResolution event returns wrongly.
Scalable text graphics do not display correctly after you save and reopen a document.
Set FileMetadata.FullFileName does not update the path on dialog boxes of Make Part/Make Component.
The position of Leader note text flips when you update a drawing document in invisible mode.
Return to Top



Assembly Modeling


Alpha sort component command works slowly in one large assembly.
Assembly work features are named to the English language when you install SP1 on a German localized Inventor.
Cannot select a COG sphere after you show COG.
Elements in an assembly pattern cannot be made visible if the pattern is not visible.
Grip Snap does not allow Precise input, and freezes after accepting only one digit.
Incorrect result shows when you use iMate to place a component with the option "Automatically generate iMates on place".
Insert constraint does not work on a folded part.
Inventor shows the last used LOD before save rather than the LOD selected during open.
Mass doubles when you create a Substitute LOD.
NG: Bill of Materials shows incorrect quantity for components in nested patterns when the pattern count is controlled by the iAssembly table.
NG: In an assembly pattern, when the total occurrence count of a component becomes too big, the performance is very slow.
Sheet metal components in an assembly do not update when you invoke a Rebuild All.
The assembly browser does not return to the top level assembly after an edit to the weld folder in a subassembly.
The Weld features in the authored iCopy templates are lost after you instance an iCopy.
Transitional constraint fails during driving constraint.
Return to Top



Content Center


A crash occurs when you update one special and remote custom library.
Column Properties Expression settings do not work if there are two or more custom parameters.
Families with file names containing $ are not treated as standard components.
Replace from Content Center replaces the length of the replaced parts with the default length for Structural Shapes Families.
The Change Size dialog box does not show the current size for the structural shapes families published from iParts.
Return to Top


Design Accelerator




Return to Top

-->



Direct Manipulation


A crash occurs in commands to create or modify a model if you cancel after measuring on a mini toolbar.
A crash occurs when you select and drag the face on one special data.
Invalid value in the mini tool bar does not change to red after you insert the measured value.
NG: On edit, wrong focus on the mini tool bar occurs when you hover the mouse on a browser node.
Create Fillet, Create Chamfer and Edit Extrude commands started from contextual mini toolbars had wrong prompting in the status bar.
Return to Top



Drawing Manager


Fixed incorrect "Member out of date" notification in Drawing view browser node.
NG: Center marks dimension incorrectly to the ends of a slot that is created with the extrude feature from a tangent plane.
NG: CER: A crash sometimes occurs when you change the column width in a parts list that displays an iProperty string containing a tab character.
NG: In drawings, you cannot retrieve a dimension for a feature from a multiple-use shared sketch when features based on it are unsuppressed.
NG: Unable to balloon components promoted from a table replaced iAssembly with a phantom BOM structure.
NG: View Cube settings are not accessible while you create a custom drawing view.
Some retrieve dimensions that do not project to an XY sheet plane, jump after model updating.
When you open a drawing with Customer Templates on Vista and Windows 7, the message "an unnamed file has a bad format" displays.
Return to Top


DWG/DWF




Return to Top




ESKD




Return to Top

-->



Framework


CER: A crash occurs when you bring up two or more Open File dialog boxes through Inventor API.
CER: A crash occurs when you invoke a Work Plane feature from the search box in the Application Menu.
CER: A crash occurs when you quickly activate the Open Document list two or more times from Document Tabs.
CER: A crash occurs when there is a "Set End of Part" error during the Extrude command.
CER: A crash occurs when there is a "Vector too long" error during creation of a Hole feature.
CER: A crash occurs when you switch multiple displays mode between Single and Dualview from the NVIDIA control panel.
Embedded images are lost when you save a copy of a document as a new document.
NG: In the Color Style edit box, the maximum texture scale is limited to 1000%.
No warning dialog box displays when you open a file from the MRU (most recently used) list, even if this file is not in the active project.
Pressing the S key does not create a 2D Sketch on a selected Work Plane.
The visibility option on the context menu does not work well for inserted images in Drawing documents.
Return to Top



Frame Generator


After you update a frame member, its part number is reset, even if the option "Get Frame Member's Part Number from Content Center" is cleared.
Some assemblies that consist of frame members generated by Frame Generator did not migrate correctly in Inventor 2011 RTM/SP1.
Return to Top


Fusion




Return to Top

-->



Graphics


CER: Inventor crashes after finishing an animation in Stress Analysis with Dynamic Section on.
CER: Inventor crashes in a drawing file if you hover the mouse on a logo picture while you click "Home" to zoom.
CER: Inventor crashes when you edit a sketch after using undo and redo several times.
Line weights are not visible after you pan.
NG: Draft Analysis gives incorrect results in graphics compatibility mode on Windows XP.
Zebra Analysis does not work well with German operating system settings.
Return to Top



iLogic


iLogic Activation Error message no longer displays (and prevents iLogic from loading) if there is a corrupted user.config file.
Return to Top



Part Modeling


All assembly constraints are lost when you modify iParts.
Bitmap is not visible in the title block if it is not pre-existent in the drawing.
CER: A crash occurs when you invoke the Copy object command and select the component in an assembly.
CER: Inventor crashes when you use Insert dwg in Sketch, and select PC from the network.
Inventor hangs during a Hole edit in sheet metal if you try to change the placement.
Legacy parts that incorrectly define a work plane on a non-planar face display errors on rebuild.
NG: Fixed incorrect result for Polar Moment in Cross Section analysis when the section contains multiple disconnected areas.
Unable to highlight objects during a boundary patch.
When you switch a Hole from Simple to Tapped, the thread size disregards the diameter size.
Work feature edit does not update in the 3D Sketch environment.
Return to Top



Sketch


A crash occurs when you delete 3D sketch geometry if you pause the mouse over overlapped geometries.
CER: A crash occurs when you import a .dwg with the option "no new sketch".
Return to Top



Sheet Metal


The preview for a corner chamfer does not update on changing values.
Return to Top



Studio


NG: Studio Rendering crashes sometimes on multi-core CPUs.
Return to Top


Task Scheduler




Return to Top

-->



Translators


A crash occurs when you publish some drawings with complicated views to DWF or PDF.
A retrieved model sketch that contains geometry text changes after DWGout.
An unexpected exit occurs when you edit a tapered thread that was migrated.
Cannot export derived Alias data to IGES and STEP formats.
Cannot import a Fusion DWG file into Inventor.
CER: A crash occurs when you export a face to DXF.
CER: Inventor crashes when you export IDW to DXF.
If the plane of a curve is perpendicular to the drawing paper, DWF publish project a 3D curve to a polyline, and not a line.
It takes a long time to export an Inventor .dwg as an AutoCAD Mechanical .dwg with the option "Parts only" turned on.
Missing zeroes in broken view dimensions after DWGOUT.
Imported CATIA V5 file has distorted faces in the model.
Imported JT file has incorrectly trimmed spheres.
The detail output of AEC Exchange with a Shrinkwrap assembly does not show in Revit.
Wrong characters are exported when publishing some drawings to PDF.
Return to Top



Vault


A crash occurs when you undo twice after create a note within a sketch.
Inventor Vault add-in is not loaded by default after SP1 installation, even if Vault Client is already installed.
Return to Top



Others


After you edit the model, a bolted connection requires a resolve.
Inventor crashes when you press Ctrl+F in a presentation file.
Return to Top

Defter
23.06.2011, 14:02
Zdravím,
jedna technická. SP2 pro AIS/AIP 2011 (opět) nejde aplikovat (sloučit) se síťovým obrazem? Vytvořil jsem nový síťový  obraz pro AIP 2012 (x86), úspěšně jsem jej updatoval pomocí SP1, znovu proběhnu wizardem, nabídmu mu SP2. Potud OK. Aplikace SP2 je však hotová během vteřiny, wizard se tváří jako, že vše super, ale SP2 samozřejmě v balíku chybí. Pardon, ale fakt už WTF!? (PS: jdu testnout x64 variantu, ale obávám se, že to bude jak přes kopírák).

Vladimír Michl
23.06.2011, 14:21
V Readme píšou že:
 

To merge Service Pack 2 to a deployment, create the deployment image afresh and merge all service packs by configuring Inventor at one time. Merging Service Pack 2 to the existing deployment image that has merged Service Pack 1 or Subscription Advantage Pack is not supported.
Takže by to jít asi mělo, ale osobně jsem to nezkoušel.

Defter
23.06.2011, 14:26
Aha, takže tady bude zakopaný vlčák...
 
[QUOTE=Vladimír Michl]V Readme píšou že:
 

To merge Service Pack 2 to a deployment, create the deployment image afresh and merge all service packs by configuring Inventor at one time. Merging Service Pack 2 to the existing deployment image that has merged Service Pack 1 or Subscription Advantage Pack is not supported.
 
[/QUOTE]
 
Musí se aplikovat oba najednou, nikoliv postupně. Díky, odzkouším.
M

Defter
24.06.2011, 10:53
Takže otestováno a tváří se, že to funguje, alespoň u x86 varianty. Takže správný postup je, vytvořit úplně nový síťový obraz a ten pomocí wizardu patchovat SP1 a SP2 najednou. Po nasazení přes AD/GPO na virtuální testovací mašině jede.
Nedalo mi to a tak jsem schválně prubnul podobnou metodu na Mechaniclu 2011, kde se nedařila už aplikace SP1. Navíc v Readme u SP2 je rovnou uváděno http://images.autodesk.com/adsk/files/autocad_mechanical_2011_update_2_csy.html :



---
Použití této aktualizace pro síťový administrativní obraz
POZNÁMKA: Aktualizaci 2 nelze rozmístit do administrativního obrazu. Na pracovní stanici můžete aktualizaci 2 instalovat v případě, že již byla opravena pomocí aktualizace 1.
---
Věc se má jinak :)
Při vytváření nového image Mechaniclu 2011 nelze pomocí wizardu aplikovat ani SP1. Nakope Vás to s tím, že patch se nedá použít pro tuto verzi programu. Necháte tedy dojet holé vytváření image bez SP a pak rozeběhnete úpravu rozmístění. A hle, najednou mu ten samý balík navadí. A co víc, když rovnou přidáte i SP2, tak celé patchování image proběhne korektně až do konce a celé je to nasaditelné pomocí AD/GPO. Tedy zatím alespoň na x86 variantě.
FAKT tohle mi hlava nebere :/
 Defter2011-06-24 13:06:11