https://www.cadforum.cz/forum_en/ Mon, 25 May 2026 11:49:42 +0000 Sat, 08 Feb 2014 16:31:56 +0000 http://blogs.law.harvard.edu/tech/rss Web Wiz Forums 12.04 360 https://www.cadforum.cz/forum_en/RSS_post_feed.asp?TID=10031 https://www.cadforum.cz/forum_en/forum_images/web_wiz_forums.png https://www.cadforum.cz/forum_en/ https://www.cadforum.cz/forum_en/forum_posts.asp?TID=10031&PID=25958&title=xref#25958 Author: John Connor
Subject: 10031
Posted: 08.Feb.2014 at 16:31

Are the xrefs stored on a network drive?

It would be nice if you provided ALL the information up front in your first post.

To repath your xrefs, without opening each drawing, use the Reference Manager.

AdRefMan.exe




Edited by John Connor - 08.Feb.2014 at 16:41]]> Sat, 08 Feb 2014 16:31:56 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=10031&PID=25958&title=xref#25958 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=10031&PID=25951&title=xref#25951 Author: pytha
Subject: 10031
Posted: 07.Feb.2014 at 23:11

if I move from workstation. xref are not connect.
I need them again each conect. much work can conect it not automaticl.?]]> Fri, 07 Feb 2014 23:11:59 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=10031&PID=25951&title=xref#25951 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=10031&PID=25949&title=xref#25949 Author: John Connor
Subject: 10031
Posted: 07.Feb.2014 at 22:28

Here is a link to a thread that contains a lisp routine written by BlackBox to set the path of an Xref.  Maybe that's what you are looking for?

http://forums.augi.com/showthread.php?123746-Lisp-to-set-Xref-path
]]> Fri, 07 Feb 2014 22:28:01 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=10031&PID=25949&title=xref#25949 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=10031&PID=25948&title=xref#25948 Author: John Connor
Subject: 10031
Posted: 07.Feb.2014 at 22:20

There are three path options for a xref.  They are...

No path

Full path

Relative path

Which one do you normally use?

Are you looking for a lisp routine to automate the process?

You question just doesn't seem to make much sense.
]]> Fri, 07 Feb 2014 22:20:54 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=10031&PID=25948&title=xref#25948 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=10031&PID=25947&title=xref#25947 Author: pytha
Subject: 10031
Posted: 07.Feb.2014 at 19:46

Can you at xref automatically his new path.]]> Fri, 07 Feb 2014 19:46:44 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=10031&PID=25947&title=xref#25947