CAD Forum discussion (EN) : Spline boundary for hatch https://www.cadforum.cz/forum_en/ Mon, 01 Jun 2026 04:36:41 +0000 Sat, 23 Feb 2008 13:26:06 +0000 http://blogs.law.harvard.edu/tech/rss Web Wiz Forums 12.04 360 https://www.cadforum.cz/forum_en/RSS_post_feed.asp?TID=507 <![CDATA[CAD Forum discussion (EN)]]> https://www.cadforum.cz/forum_en/forum_images/web_wiz_forums.png https://www.cadforum.cz/forum_en/ <![CDATA[Spline boundary for hatch : Can you post your drawing to...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=507&PID=1266&title=spline-boundary-for-hatch#1266 Author: Arben.Allaraj
Subject: 507
Posted: 23.Feb.2008 at 13:26

 
 Can you post your drawing to me? arben.allaraj@gmail.com
 
]]> Sat, 23 Feb 2008 13:26:06 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=507&PID=1266&title=spline-boundary-for-hatch#1266 <![CDATA[Spline boundary for hatch : Thanks for your reply.I&#039;ve...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=507&PID=1259&title=spline-boundary-for-hatch#1259 Author: dxsubomni
Subject: 507
Posted: 22.Feb.2008 at 18:38

Thanks for your reply.

I've actually looked into this already and it's not going to work for me.  Polylines aren't practical in this drawing for editing and cosmetic reasons.  I need to be able to update it periodically as new data is recorded.

Any other ideas?
]]> Fri, 22 Feb 2008 18:38:38 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=507&PID=1259&title=spline-boundary-for-hatch#1259 <![CDATA[Spline boundary for hatch : WELCOME TO CADFORUM. I think...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=507&PID=1253&title=spline-boundary-for-hatch#1253 Author: Arben.Allaraj
Subject: 507
Posted: 22.Feb.2008 at 10:42

 
 WELCOME TO CADFORUM.
 
I think you should convert spline to pline by method  below and try again.
 
http://www.cadforum.cz/cadforum_en/qaID.asp?tip=2103
]]> Fri, 22 Feb 2008 10:42:14 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=507&PID=1253&title=spline-boundary-for-hatch#1253 <![CDATA[Spline boundary for hatch : Hey everyoneFirst off, sorry if...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=507&PID=1252&title=spline-boundary-for-hatch#1252 Author: dxsubomni
Subject: 507
Posted: 22.Feb.2008 at 02:18

Hey everyone

First off, sorry if the answer to my question is completely obvious: I'm fairly new to AutoCAD.

Using 2008, I'm trying to draw hatches with splines as boundaries.  It works fine until I try to add hatches after closing and reopening autocad (the next day, for example).  It then seems to just ignore splines at random and hatch right through them to the next line or polyline.  Sometimes the section that is ignored includes two splines connected at the ends, and sometimes it's one solid spline.  I haven't been able to figure out any pattern or consistency to which splines it ignores. 

It's not really feasible for me to use polylines instead.  So far the only solution I've been able to come up with is to redraw the spline, but that slows down my work considerably and I'm hoping for a quicker and easier answer.

What am I doing wrong?
]]> Fri, 22 Feb 2008 02:18:13 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=507&PID=1252&title=spline-boundary-for-hatch#1252