CAD Forum discussion (EN) : Help with extrude command https://www.cadforum.cz/forum_en/ Sun, 31 May 2026 20:54:55 +0000 Mon, 26 Dec 2011 12:33:54 +0000 http://blogs.law.harvard.edu/tech/rss Web Wiz Forums 12.04 360 https://www.cadforum.cz/forum_en/RSS_post_feed.asp?TID=7073 <![CDATA[CAD Forum discussion (EN)]]> https://www.cadforum.cz/forum_en/forum_images/web_wiz_forums.png https://www.cadforum.cz/forum_en/ <![CDATA[Help with extrude command : YES!...That´s it!...Thank...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7073&PID=18269&title=help-with-extrude-command#18269 Author: miroslav_s
Subject: 7073
Posted: 26.Dec.2011 at 12:33

YES!...That´s it!...Thank you. For me it is better solution cause I never used SLICE command before. Thanks once again for helping.
]]> Mon, 26 Dec 2011 12:33:54 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7073&PID=18269&title=help-with-extrude-command#18269 <![CDATA[Help with extrude command : Yes there is. Draw the wall profile...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7073&PID=18268&title=help-with-extrude-command#18268 Author: John Connor
Subject: 7073
Posted: 26.Dec.2011 at 12:27

Yes there is.  Draw the wall profile in the vertical to match the roof line and then extrude it.  You do not have to do all your extrusions from a 2D plan view.]]> Mon, 26 Dec 2011 12:27:51 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7073&PID=18268&title=help-with-extrude-command#18268 <![CDATA[Help with extrude command : Hello,Thanks again for answering...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7073&PID=18267&title=help-with-extrude-command#18267 Author: miroslav_s
Subject: 7073
Posted: 26.Dec.2011 at 10:59

Hello,

Thanks again for answering mail question. OK, I will try the SLICE command, but I was wondering there got to be another way. For example if I draw an oblique line (representing the roof) and the when I use the extrude command to “pull” up the wall so that the wall meet the roof line. This way I would not need first to extrude the wall beyond the roof and then use slice command to cut of the parts of the walls that I don´t need.

 Thanks once again for helping me.

Best regards

]]> Mon, 26 Dec 2011 10:59:34 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7073&PID=18267&title=help-with-extrude-command#18267 <![CDATA[Help with extrude command : I can&#039;t seem to &#034;see&#034;...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7073&PID=18265&title=help-with-extrude-command#18265 Author: John Connor
Subject: 7073
Posted: 26.Dec.2011 at 01:48

I can't seem to "see" your picture (miropicture.jpg).

Can't you use the SLICE command to solve your problem?
]]> Mon, 26 Dec 2011 01:48:04 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7073&PID=18265&title=help-with-extrude-command#18265 <![CDATA[Help with extrude command : Hi, this is my first post...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7073&PID=18264&title=help-with-extrude-command#18264 Author: miroslav_s
Subject: 7073
Posted: 25.Dec.2011 at 23:26

Hi, this is my first post so be kind to me :)

My problem: I attached a picture so in case I explain bad my problem you can see the picture. On the picture you can see a wall and a roof. Now a used command extrude to pull up the wall. I would like the wall to follow the line of the roof. One corner is OK but as you can se the wall is going over the roof. Everytime a use the extrude command the upper wallside is allways parallel to th bottom. Now is the roof is design like on this picture how can I tell the autocad to extrude the wall only to the roof and not beyond. God, i hope I explained good my problem. Thanks in advance for your help. Best regards, Miropicture.jpg

]]> Sun, 25 Dec 2011 23:26:36 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7073&PID=18264&title=help-with-extrude-command#18264