CAD Forum discussion (EN) : to join lines as polyline https://www.cadforum.cz/forum_en/ Sat, 16 May 2026 14:52:26 +0000 Fri, 06 Apr 2012 12:58:48 +0000 http://blogs.law.harvard.edu/tech/rss Web Wiz Forums 12.04 360 https://www.cadforum.cz/forum_en/RSS_post_feed.asp?TID=7530 <![CDATA[CAD Forum discussion (EN)]]> https://www.cadforum.cz/forum_en/forum_images/web_wiz_forums.png https://www.cadforum.cz/forum_en/ <![CDATA[to join lines as polyline : You&#039;ll have to do a search...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7530&PID=19732&title=to-join-lines-as-polyline#19732 Author: John Connor
Subject: 7530
Posted: 06.Apr.2012 at 12:58

You'll have to do a search for a diesel macro that will do the same thing assuming that one even exists.]]> Fri, 06 Apr 2012 12:58:48 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7530&PID=19732&title=to-join-lines-as-polyline#19732 <![CDATA[to join lines as polyline : Hi guys, Thank you for your...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7530&PID=19730&title=to-join-lines-as-polyline#19730 Author: hgf_21_xy
Subject: 7530
Posted: 06.Apr.2012 at 10:13

Hi guys,
 
Thank you for your reply!
 
Unfortunately I can not use "overkill" command, since I am working with AutoCAD LT 2010.
 
Do you know other ways to check?


Edited by hgf_21_xy - 06.Apr.2012 at 10:14]]> Fri, 06 Apr 2012 10:13:50 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7530&PID=19730&title=to-join-lines-as-polyline#19730 <![CDATA[to join lines as polyline : OVERKILL is the command for the...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7530&PID=19485&title=to-join-lines-as-polyline#19485 Author: heinsite
Subject: 7530
Posted: 19.Mar.2012 at 23:29

OVERKILL is the command for the job...but it's version-dependant. 
 
OVERKILL used to be only an Express Tools command and goes back to about 2005 or so.  It only became available in LT in 2012 as far as I know.  So unless the OP has the full version of AutoCAD or LT 2012 overkill might not be available.
 
Dave.
]]> Mon, 19 Mar 2012 23:29:05 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7530&PID=19485&title=to-join-lines-as-polyline#19485 <![CDATA[to join lines as polyline : I think you can clean up overlapping...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7530&PID=19479&title=to-join-lines-as-polyline#19479 Author: John Connor
Subject: 7530
Posted: 19.Mar.2012 at 10:52

I think you can clean up overlapping lines with the OVERKILL command.

As far as connecting lines you could use the JOIN command with a "fuzz" factor of "0".
]]> Mon, 19 Mar 2012 10:52:07 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7530&PID=19479&title=to-join-lines-as-polyline#19479 <![CDATA[to join lines as polyline : hi, did anyone know a way...]]> https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7530&PID=19477&title=to-join-lines-as-polyline#19477 Author: hgf_21_xy
Subject: 7530
Posted: 19.Mar.2012 at 08:39

hi,
 
did anyone know a way or command to quickly check if the lines are overlapped or disconnected in the drawing??Question
 
it really gave me a pain due to that, becasue i was always trying to find out where the lines were overlapped or disconnected when they could not be joint as a polyline.
 
thanks!


Edited by hgf_21_xy - 19.Mar.2012 at 08:40]]> Mon, 19 Mar 2012 08:39:45 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=7530&PID=19477&title=to-join-lines-as-polyline#19477