https://www.cadforum.cz/forum_en/ Mon, 20 Apr 2026 01:03:39 +0000 Thu, 05 Dec 2013 16:54:49 +0000 http://blogs.law.harvard.edu/tech/rss Web Wiz Forums 12.04 360 https://www.cadforum.cz/forum_en/RSS_post_feed.asp?TID=9869 https://www.cadforum.cz/forum_en/forum_images/web_wiz_forums.png https://www.cadforum.cz/forum_en/ https://www.cadforum.cz/forum_en/forum_posts.asp?TID=9869&PID=25381&title=measure-command-error#25381 Author: John Connor
Subject: 9869
Posted: 05.Dec.2013 at 16:54

SNAP can be enabled merely by accidentally hitting the F9 key with your fingers.  Any other way it is enabled would be deliberate unless you were using a custom lisp routine that required SNAP to be enabled and when finished it failed to disable the command.  This is bad form as far as lisp gurus are concerned.
]]> Thu, 05 Dec 2013 16:54:49 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=9869&PID=25381&title=measure-command-error#25381 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=9869&PID=25374&title=measure-command-error#25374 Author: LouLou7
Subject: 9869
Posted: 05.Dec.2013 at 16:13

It's the Snap settings, untick the snap settings and then you will have no problems, sometimes it does tick this, without knowing, the comand can be quite frustrating.
]]> Thu, 05 Dec 2013 16:13:47 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=9869&PID=25374&title=measure-command-error#25374 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=9869&PID=25372&title=measure-command-error#25372 Author: bdeckman
Subject: 9869
Posted: 05.Dec.2013 at 14:03

I was also thinking maybe it had to do with not being in model space. I will check both of those today.]]> Thu, 05 Dec 2013 14:03:31 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=9869&PID=25372&title=measure-command-error#25372 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=9869&PID=25365&title=measure-command-error#25365 Author: John Connor
Subject: 9869
Posted: 05.Dec.2013 at 00:01

Your first choice of action should never be uninstalling/reinstalling AutoCAD.  That would be like swapping out the gas tank on your car because you ran out of gas.

Maybe it's jumping because the operator has SNAP enabled.
]]> Thu, 05 Dec 2013 00:01:47 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=9869&PID=25365&title=measure-command-error#25365 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=9869&PID=25362&title=measure-command-error#25362 Author: bdeckman
Subject: 9869
Posted: 04.Dec.2013 at 20:04

We are having an issue on one of our PC's where the operator attempts to use the measure command and start from a point but the command "jumps" and gives the wrong point in the measurement. I hate doing a reinstall, we just did one about a month ago. Any ideas?]]> Wed, 04 Dec 2013 20:04:19 +0000 https://www.cadforum.cz/forum_en/forum_posts.asp?TID=9869&PID=25362&title=measure-command-error#25362