Stair
Printed From: CAD Forum
Category: EN
Forum Name: AutoCAD
Forum Description: Discussion about AutoCAD and AutoCAD LT, viewers, DWG and DWF formats, Design Review, AutoCAD 360, add-ons
URL: https://www.cadforum.cz/forum_en/forum_posts.asp?TID=9699
Printed Date: 22.Apr.2026 at 00:06
Topic: Stair
Posted By: Halling51
Subject: Stair
Date Posted: 05.Oct.2013 at 04:56
|
Hi Looking for help to make a CAD drawing of a stair. I can provide allmeasuring but I don't know much about CAD!  I do want all in mm. Sincerely Steinar NORWAY ------------- Sincerely Steinar |
Replies:
Posted By: John Connor
Date Posted: 05.Oct.2013 at 12:39
|
Will you be doing this is 2D or 3D? Do you have all the necessary dimensions (riser height, tread depth, overall height between floors, etc.)? What size stringers will you be utilizing? Will you also be including a railing, balusters, and newel post(s)? Will a landing be required? ------------- "Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance." <<AutoCAD 2015>> |
Posted By: Halling51
Date Posted: 06.Oct.2013 at 12:18
|
Hi Thanks for the return reply. It might be easiers for me to send PM to you about this? I will be taking a picture and make excact measuring today I hope. It depend on the person I am going to make it for if he is at the cabin. I think 3D would suite me best in mm Thanks in advance Steinar VissebrĂĄten If you want here is my adresse.: bratt@vissebraaten.no ------------- Sincerely Steinar |
Posted By: John Connor
Date Posted: 06.Oct.2013 at 13:31
|
Have you done any work in 3D? ------------- "Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance." <<AutoCAD 2015>> |
Posted By: Halling51
Date Posted: 06.Oct.2013 at 15:38
|
OK, 2D then The measuring is as following: Each tread will be: 40mm Total raise is: 2435 mm Total run is: 1780 mm Width is: 788 (785 best fit) mm (outside to outside) Lenght of stringer I hope will be from the drawing. I think from bottom floor and the 3 first tread will be the curve. As the first tread will be turned only at the back of the tread. Seen from bottom - up left. From tread no. 4 will be the same size. The tread nosing shold be nothing. He want an open stringer on each side as the wall is on right and about 300 mm from the top. He also want raisers between each tread. Hope this is ok. If I do have an addresse I can provide you 3 pictures how it is today (very bad done handwork) Steinar ------------- Sincerely Steinar |
Posted By: Halling51
Date Posted: 06.Oct.2013 at 15:49
|
Forgot to say I think 250 mm deapt would be fine +- ofcourse. Basic would be around 425mm as a rule. 250 tread and 175mm raiser. Steinar ------------- Sincerely Steinar |
Posted By: John Connor
Date Posted: 06.Oct.2013 at 15:55
|
You would be better off uploading the pictures here. Maybe one of the forum members will take on the task of drawing it up. ------------- "Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance." <<AutoCAD 2015>> |
Posted By: Halling51
Date Posted: 06.Oct.2013 at 18:26
|
Hi again. I am not sure how but I have made a ling for each of them. rukkedalen.com/stair_001.jpg rukkedalen.com/stair_002.jpg The third picture show the disaster where the stair turns. I have never seen so bad job. My thoughts was to make 1,2 and 3rd. tread as the first turning of the stair and then the rest the same. It is a steap stair but done better it would be ok for the users. When you know the measurements and have the pictures I hope to get the drawing. I do appreciate any solution that will make it much better then the pistures. The raisers is not the same and I hope to make them the same. rukkedalen.com/stair_003.jpg I hope you copy and past the link. Thanks so much in advance. I amworking on my skills in CAD but for me it is not quick nor easy. ------------- Sincerely Steinar |
Posted By: John Connor
Date Posted: 06.Oct.2013 at 20:36
|
Is there a dimensioned floor plan? Looks like there could be an obstacle or two to work around. ------------- "Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance." <<AutoCAD 2015>> |
Posted By: Halling51
Date Posted: 07.Oct.2013 at 00:45
|
I am not sure what you mean. The floor is plain and nothing in the way in the opening. ------------- Sincerely Steinar |
Posted By: philippe JOSEPH
Date Posted: 07.Oct.2013 at 09:59
|
Halling51, you have right here in the site examples of stairs in :
Cad Blocks, launch a search with the word STAIR and you have 10 pages of DWG files.
|
Posted By: John Connor
Date Posted: 07.Oct.2013 at 12:16
|
If there is nothing in the way then I would eliminate the curve in the stair and add a landing. Triangular shaped stairs are dangerous. ------------- "Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance." <<AutoCAD 2015>> |
Posted By: Halling51
Date Posted: 16.Oct.2013 at 16:53
|
As of now - no reply or qualified help. Thanks Connor for your effort. ------------- Sincerely Steinar |