![CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]](/common/arkance_186.png "CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]")
CAD FORUM - TIPS & TRICKS | UTILITIES | DISCUSSION | BLOCKS | SUPPORT | HELP & ADVICE
Over 1.096.000 registered users (EN+CZ).
AutoCAD tips, Inventor tips, Revit tips.
Try the new precise Engineering calculator and the updated Barcode generator.
New AutoCAD 2026 commands and variables.
Discussion forum
?CAD discussions, advices, exchange of experience
CAD discussion forum - ask any CAD-related questions here, share your CAD knowledge on AutoCAD, Inventor, Revit and other Autodesk software with your peers from all over the world. To start a new topic, choose an appropriate forum.
Please abide by the rules of this forum.
This is a peer-to-peer forum. The forum doesn't replace the official direct technical support provided by ARKANCE for its customers.
How to post questions: register or login, go to the specific forum and click the NEW TOPIC button.
|
3D - 2D
Post Reply 
|
| Author | |
snowchip 
Newbie 
Joined: 15.Feb.2008 Location: United States Status: Offline Points: 1 |
 Topic: 3D - 2DPosted: 15.Feb.2008 at 19:41 |
|
Hi All,
I need to convert a 3D inventor drawing to a 2D. anyone know how to do it? i need all the linked files to be there too. any help would be appreciated.
Thanks
Snowchip |
|
 |
|
|
simprisalide
Newbie
Joined: 15.Feb.2008 Location: Italy Status: Offline Points: 2 |
Posted: 15.Feb.2008 at 21:14 |
|
2D drawing, in Inventor, is an IDW file where you can create every views of piece/assembly and than put dimensions. |
|
|
|
|
Arben.Allaraj
Senior Member 
Joined: 14.Nov.2007 Location: Albania Using: AutoCAD 2008 Status: Offline Points: 602 |
Posted: 16.Feb.2008 at 12:08 |
|
Welcome to CADFORUM.
You should as exporting files form Inventor to AutoCAD and in AutoCAD
convert 3D to 2D.
For this there is a tip below.Tip 4123 Edited by Arben.Allaraj - 16.Feb.2008 at 12:09 |
|
|
Ing Arben.Allaraj
http://cad-drafting-corner.blogspot.com |
|
|
|
|
dictum
Newbie
Joined: 26.Feb.2008 Location: United States Status: Offline Points: 7 |
Posted: 26.Feb.2008 at 22:37 |
|
Check This Out
Good discussion on creating a 2d drawing in Autodesk from a 3D model, including a video walk through. Hope it's helpful. Edited by dictum - 26.Feb.2008 at 22:40 |
|
|
|
Topic Options|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
This page was generated in 0,156 seconds.
CADforum
Tips and tricks, support, utilities, help, discussions on AutoCAD, LT, Inventor, Revit, Map, Civil 3D, 3ds Max, Fusion, Forma, Vault, PowerMill and other Autodesk software (community support by ARKANCE). See About CADforum.
Copyright © 2025 | Advertise with us | Online privacy
