![CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]](/common/arkance_186.png "CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]")
CAD FORUM - TIPS & TRICKS | UTILITIES | DISCUSSION | BLOCKS | SUPPORT | HELP & ADVICE
Over 1.104.000 registered users (EN+CZ).
AutoCAD tips, Inventor tips, Revit tips, Civil tips, Fusion tips.
Try the new precise Engineering calculator.
New AutoCAD 2026 commands and sys.variables and env.variables,.
Discussion forum
?CAD discussions, advices, exchange of experience
CAD discussion forum - ask any CAD-related questions here, share your CAD knowledge on AutoCAD, Inventor, Revit and other Autodesk software with your peers from all over the world. To start a new topic, choose an appropriate forum.
Please abide by the rules of this forum.
This is a peer-to-peer forum. The forum doesn't replace the official direct technical support provided by ARKANCE for its customers.
How to post questions: register or login, go to the specific forum and click the NEW TOPIC button.
About use "overkill" command in Autocad 2022 |
Post Reply 
|
| Author | |
atobag 
Newbie 
Joined: 05.Sep.2025 Location: Italy Using: autocad 2022 Status: Offline Points: 3 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: About use "overkill" command in Autocad 2022Posted: 05.Sep.2025 at 21:11 |
|
Hi to all, new here and not expert in Autocad. As for CAD Tip #3525 i try to remove double line of same layer on plane figure stacked lines - overlaid. In Autocad 2022 (not Map) i used a various set options in dialog box of "overkill" command (brush icon) whitout success. About CAD Tip #14477, i need to remove only double line: it's necessary run it? Any suggestion ? (Please note, in the complex drawings for photoengraving processing may occur hundred of this situations and they are not allowed) |
|
 |
|
|
Vladimir Michl
Moderator Group 
Arkance Systems CZ Joined: 26.Jul.2007 Location: Czech Republic Using: Autodesk software Status: Offline Points: 2140 |
Post Options
Thanks(1)
Quote Reply
Posted: 06.Sep.2025 at 20:52 |
|
Tip #14477 won't help in this case. The Overkill command resolves only duplicate (or almost duplicate) lines. But your drawing may contain overlaid lines in diferent elevations, or segmented lines over a single-segment line or other special cases.
|
|
|
Vladimir Michl (moderator)
ARKANCE - https://arkance.world - Autodesk Platinum Partner |
|
|
|
|
atobag
Newbie
Joined: 05.Sep.2025 Location: Italy Using: autocad 2022 Status: Offline Points: 3 |
Post Options
Thanks(0)
Quote Reply
Posted: 12.Sep.2025 at 12:11 |
|
Thanks for a reply Vladimir. Gently, do you know if there are other ways? Regards.
|
|
|
|
|
Vladimir Michl
Moderator Group
Arkance Systems CZ Joined: 26.Jul.2007 Location: Czech Republic Using: Autodesk software Status: Offline Points: 2140 |
Post Options
Thanks(0)
Quote Reply
Posted: 12.Sep.2025 at 12:56 |
|
There are pobably other ways but I will need to see the drawing or at least a part of it to explore the specific case of overlaps.
|
|
|
Vladimir Michl (moderator)
ARKANCE - https://arkance.world - Autodesk Platinum Partner |
|
|
|
Topic Options|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
This page was generated in 0,068 seconds.
CADforum
Tips and tricks, support, utilities, help, discussions on AutoCAD, LT, Inventor, Revit, Map, Civil 3D, 3ds Max, Fusion, Forma, Vault, PowerMill and other Autodesk software (community support by ARKANCE). See About CADforum.
Copyright © 2025 | Advertise with us | Online privacy
