![CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]](/common/arkance_186.png "CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]")
CAD FORUM - TIPS & TRICKS | UTILITIES | DISCUSSION | BLOCKS | SUPPORT | HELP & ADVICE
Over 1.110.000 registered users (EN+CZ).
AutoCAD tips, Inventor tips, Revit tips, Civil tips, Fusion tips.
The new Beam calculator and Spirograph generator in the Converters section.
Discussion forum
?CAD discussions, advices, exchange of experience
CAD discussion forum - ask any CAD-related questions here, share your CAD knowledge on AutoCAD, Inventor, Revit and other Autodesk software with your peers from all over the world. To start a new topic, choose an appropriate forum.
Please abide by the rules of this forum.
This is a peer-to-peer forum. The forum doesn't replace the official direct technical support provided by ARKANCE for its customers.
How to post questions: register or login, go to the specific forum and click the NEW TOPIC button.
|
How to create individual outlined polylines?
Post Reply 
|
| Author | |
romkeris 
Newbie 
Joined: 03.Dec.2010 Location: Lithuania Using: Autocad Status: Offline Points: 3 |
 Topic: How to create individual outlined polylines?Posted: 05.Dec.2010 at 17:29 |
Fine, never knew about mline... :) But quite frequently I also need to create rounded corners. Fillet command doesn't work with mlines.
|
|
 |
|
|
Cad64
Senior Member 
Joined: 17.Apr.2010 Location: United States Using: Autocad 2011, 3DS Max 2011, Photoshop CS5 Status: Offline Points: 491 |
Posted: 05.Dec.2010 at 16:34 |
|
For the unfilled polylines, just draw them using multilines. Check your Autocad Help files for information on how to set up the spacing, end caps, etc.
Commands: MLINE, MLSTYLE, MLEDIT. Edited by Cad64 - 05.Dec.2010 at 16:34 |
|
|
Online Portfolio: http://www.rdeweese.com/
|
|
|
|
|
tulip3D
Senior Member
Joined: 23.Jul.2009 Location: United States Using: AutoCAD2011, Inventor2011 Status: Offline Points: 427 |
Posted: 03.Dec.2010 at 18:31 |
|
...hmmm...maybe use the *pedit* command? select the individual lines and make separate shapes?
|
|
|
|
|
romkeris
Newbie
Joined: 03.Dec.2010 Location: Lithuania Using: Autocad Status: Offline Points: 3 |
Posted: 03.Dec.2010 at 15:41 |
|
Is it possible to create individual outlined polylines? I cannot use fillmode command because some polylines must be filled and some not in the same drawing. Thanks :)
Edited by romkeris - 03.Dec.2010 at 15:43 |
|
|
|
Topic Options
Cad64 wrote:|
Post Reply
|
|
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
This page was generated in 0,063 seconds.
CADforum
Tips and tricks, support, utilities, help, discussions on AutoCAD, LT, Inventor, Revit, Map, Civil 3D, 3ds Max, Fusion, Forma, Vault, PowerMill and other Autodesk software (community support by ARKANCE). See About CADforum.
Copyright © 2026 | Advertise with us | Online privacy
