CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz] ARKANCE | CONTACT - CZ | SK | EN | DE
Over 1.102.000 registered users (EN+CZ). AutoCAD tips, Inventor tips, Revit tips, Civil tips, Fusion tips. Try the new precise Engineering calculator. New AutoCAD 2026 commands and sys.variables and env.variables,.
RSS channel - CAD tips RSS tips
RSS discussions

Discussion Discussion forum

?
CAD discussions, advices, exchange of experience

CAD Forum - Homepage CAD discussion forum - ask any CAD-related questions here, share your CAD knowledge on AutoCAD, Inventor, Revit and other Autodesk software with your peers from all over the world. To start a new topic, choose an appropriate forum.

Please abide by the rules of this forum.
This is a peer-to-peer forum. The forum doesn't replace the official direct technical support provided by ARKANCE for its customers.
How to post questions: register or login, go to the specific forum and click the NEW TOPIC button.
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Topic ClosedRead only / write protection
 Post Reply Post Reply
Author
  Topic Search Topic Search  Topic Options Topic Options
John Connor View Drop Down
Senior Member
Senior Member


Joined: 01.Feb.2011
Location: United States
Using: AutoCAD 2018
Status: Offline
Points: 7175 		Direct Link To This Post Topic: Read only / write protection
    Posted: 04.Jan.2013 at 14:54
What is the problem with your templates?
"Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance."

<<AutoCAD 2015>>
Back to Top
Alan Reed View Drop Down
Newbie
Newbie


Joined: 04.May.2010
Location: United Kingdom
Using: AutoCAD LT2016
Status: Offline
Points: 2 		Direct Link To This Post Posted: 04.Jan.2013 at 12:22
Thanks John.
 
I am working from a stand alone system.
I have solved one problem by changing the Administrator settings and this then allows me access to the drawing files. But still have a problem with templates. The files are all on my internal hard drive. 
 
Regards
 
Alan
Alan Reed
Back to Top
John Connor View Drop Down
Senior Member
Senior Member


Joined: 01.Feb.2011
Location: United States
Using: AutoCAD 2018
Status: Offline
Points: 7175 		Direct Link To This Post Posted: 04.Jan.2013 at 11:33
If you are working off a network one possible cause is a timing conflict involving your server.

Where are you attempting to save your DWG files to?  What is the full path?


Edited by John Connor - 04.Jan.2013 at 11:35
"Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance."

<<AutoCAD 2015>>
Back to Top
Alan Reed View Drop Down
Newbie
Newbie


Joined: 04.May.2010
Location: United Kingdom
Using: AutoCAD LT2016
Status: Offline
Points: 2 		Direct Link To This Post Posted: 03.Jan.2013 at 16:07
Due to a computer failure I have had to reinstall Autocad LT2013 on a new computer and I obtained the activation code. However when I open a drawing (installed onto the new computer C:drive) I keep getting 'this file is read only' even after unchecking the relevant box in drawing properties. I have attempted to copy the information into a new file but no luck, 'this file is write protected.
Any help to remove this problem would be greatly appreciated.
 
Regards
 
Alan
Alan Reed
Back to Top

Related CAD tips:


 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down



This page was generated in 0,266 seconds.
CADforum
CADforum
Tips and tricks, support, utilities, help, discussions on AutoCAD, LT, Inventor, Revit, Map, Civil 3D, 3ds Max, Fusion, Forma, Vault, PowerMill and other Autodesk software (community support by ARKANCE). See About CADforum.
Copyright © 2025 | Advertise with us | Online privacy
ARKANCE - Autodesk Platinum Partner & Training Center & Services Partner
CONTACT:
webmaster.cz@arkance.world | tel. +420 910 970 111
FB LN TW YT TW Blog RSS
.
TOPlist