![CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]](/common/arkance_186.png "CAD Forum - tips, tricks, discussion and utilities for AutoCAD, Inventor, Revit and other Autodesk products [www.cadforum.cz]")
CAD FORUM - TIPS & TRICKS | UTILITIES | DISCUSSION | BLOCKS | SUPPORT | HELP & ADVICE
Over 1.106.000 registered users (EN+CZ).
AutoCAD tips, Inventor tips, Revit tips, Civil tips, Fusion tips.
Try the new precise Engineering calculator.
New AutoCAD 2026 commands and sys.variables and env.variables,.
Discussion forum
?CAD discussions, advices, exchange of experience
CAD discussion forum - ask any CAD-related questions here, share your CAD knowledge on AutoCAD, Inventor, Revit and other Autodesk software with your peers from all over the world. To start a new topic, choose an appropriate forum.
Please abide by the rules of this forum.
This is a peer-to-peer forum. The forum doesn't replace the official direct technical support provided by ARKANCE for its customers.
How to post questions: register or login, go to the specific forum and click the NEW TOPIC button.
|
break
Post Reply 
|
Page 12> |
| Author | |
pytha 
Groupie 
Joined: 14.Jan.2010 Location: Netherlands Using: autocad2013 Status: Offline Points: 23 |
 Topic: breakPosted: 18.Dec.2013 at 11:19 |
|
Multiple lines break at the same time is that possiblehelp
|
|
|
bart
|
|
 |
|
|
John Connor
Senior Member 
Joined: 01.Feb.2011 Location: United States Using: AutoCAD 2018 Status: Offline Points: 7175 |
Posted: 18.Dec.2013 at 11:21 |
|
In theory....yes.
We need more detail though and an image would help too. Words tend to fail what an image can convey. |
|
|
"Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance."
<<AutoCAD 2015>> |
|
|
|
|
John Connor
Senior Member
Joined: 01.Feb.2011 Location: United States Using: AutoCAD 2018 Status: Offline Points: 7175 |
Posted: 18.Dec.2013 at 12:00 |
|
Well???????????????????? We're waiting.
|
|
|
"Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance."
<<AutoCAD 2015>> |
|
|
|
|
Kent Cooper
Senior Member
Joined: 12.Mar.2013 Location: United States Using: AutoCAD2020, 2023 Status: Offline Points: 686 |
Posted: 18.Dec.2013 at 14:59 |
|
Perhaps one of these will do what you're after:
and another:
Edited by Kent Cooper - 18.Dec.2013 at 15:28 |
|
|
|
|
Vladimir Michl
Moderator Group 
Arkance Systems CZ Joined: 26.Jul.2007 Location: Czech Republic Using: Autodesk software Status: Offline Points: 2144 |
Posted: 18.Dec.2013 at 15:09 |
|
If you are looking for breaking lines at all intersections, you can use the tip:
|
|
|
Vladimir Michl (moderator)
ARKANCE - https://arkance.world - Autodesk Platinum Partner |
|
|
|
|
pytha
Groupie
Joined: 14.Jan.2010 Location: Netherlands Using: autocad2013 Status: Offline Points: 23 |
Posted: 21.Dec.2013 at 10:36 |
|
I need parts drawing on the floor (FLOOR PLOT) these parts must be milled from slabs. These lines must fall within the plates. Useful if you can say breaklines outer plate
tanks |
|
|
bart
|
|
|
|
|
pytha
Groupie
Joined: 14.Jan.2010 Location: Netherlands Using: autocad2013 Status: Offline Points: 23 |
Posted: 21.Dec.2013 at 10:42 |
|
I'm looking for a routine that will select a line, then that line will be broken at points where it intersect other lines.
Or better, to draw a line which will break when intersect with other lines. 
|
|
|
bart
|
|
|
|
|
John Connor
Senior Member
Joined: 01.Feb.2011 Location: United States Using: AutoCAD 2018 Status: Offline Points: 7175 |
Posted: 21.Dec.2013 at 12:59 |
|
Did you test any of the lisp routines previously mentioned?
I am pretty sure I have seen a custom lisp routine that will break all lines at intersections with other lines. I don't recall however if the routines creates a gap or not. |
|
|
"Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance."
<<AutoCAD 2015>> |
|
|
|
|
pytha
Groupie
Joined: 14.Jan.2010 Location: Netherlands Using: autocad2013 Status: Offline Points: 23 |
Posted: 21.Dec.2013 at 13:09 |
|
Which lips routines do you mean? Is there a possibility to send me a link?
Rgds, Bart |
|
|
bart
|
|
|
|
|
John Connor
Senior Member
Joined: 01.Feb.2011 Location: United States Using: AutoCAD 2018 Status: Offline Points: 7175 |
Posted: 21.Dec.2013 at 17:46 |
|
Did you click on any of the links provided by Kent Cooper or Vladimir? There were four in total. Yes or no?
|
|
|
"Humans have a strength that cannot be measured. This is John Connor. If you are reading this, you are the resistance."
<<AutoCAD 2015>> |
|
|
|
Topic Options|
Post Reply
|
Page 12> |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
This page was generated in 0,148 seconds.
CADforum
Tips and tricks, support, utilities, help, discussions on AutoCAD, LT, Inventor, Revit, Map, Civil 3D, 3ds Max, Fusion, Forma, Vault, PowerMill and other Autodesk software (community support by ARKANCE). See About CADforum.
Copyright © 2025 | Advertise with us | Online privacy
